Dynacord V600:4 powerTANK Install Amplifier 4-Channel 600W 100V 1U

Product code: 191833

£1,064.00 inc VAT
£886.67 ex VAT

SKU: F.01U.409.543

11 in stock (more available subject to additional lead time)

11 available online
More available from supplier in 1–3 weeks
FREE delivery by WednesdayOrder by 3pm tomorrow
Click & Collect Tuesday ›Collect from us in Wembley
VisaMastercardAmerican ExpressApple PayGoogle PayPayPalPayPal Credit
1 Year Manufacturer Warranty Included

About this Product

Output: 100V line or low impedance.

The Dynacord V600:4 is a four-channel installation amplifier with 600W of total power shared across its outputs, rated at 4x 150W into 4 ohms, 8 ohms, 70V or 100V. Its powerTANK design lets one channel draw more power than another without manual set-up, so a single unit can run zones of different sizes. It suits schools, hotels, bars, retail and houses of worship, and pairs with the Dynacord VZX-8 or MXE5 processors.

4x 150W
4/8 ohm, 70V, 100V
600W
Shared total
<1W
Auto standby
1U
Rack height

Features

Four channels, 4x 150W rated into 4 ohms, 8 ohms, 70V or 100V
powerTANK: 600W total shared across channels as each zone needs it, with no configuration
Variable Load Drive gives the same rated power at any of the four load types
Four balanced inputs on two 6-pin Euroblocks, plus a parallel RJ45 amp-LINK input (AES72-1E) for single-cable wiring
High-pass and low-pass filters (24 dB/oct), input routing and peak limiter
ecoRAIL idle mode under 20W, and Auto Power Down to under 1W with no signal
Convection cooled, with a multi-speed fan for rack use without spacing or high temperatures
Power factor corrected supply, mains over/under-voltage protection
Remote on/standby contact and ready/fault relay on a 5-pin Euroblock

Specifications

Dynacord V600:4 powerTANK Install Amplifier 4-Channel 600W 100V 1U specifications
Rated output power 4x 150W into 4 ohms, 8 ohms, 70V or 100V
Total output power 600W (power sharing)
THD+N <0.1% (1/8 rated power, 1 kHz)
Signal-to-noise ratio >98 dB (A-weighted, ref. rated power)
Inputs 2x 6-pin Euroblock (3.81 mm), parallel 1x RJ45 amp-LINK
Maximum input level +18 dBu
Input impedance 20 kohm, active balanced
Speaker outputs 2x 4-pin Euroblock (5.08 mm)
Control port 5-pin Euroblock: remote on/standby, ready/fault relay (30 V DC, 500 mA)
Power consumption 115W at 1/8 rated power; <20W idle (ecoRAIL); <1W standby
Mains 100 to 240 V AC, 50/60 Hz, IEC C14
Operating temperature -5 to +45°C
Dimensions (H x W x D) 44.2 x 483 x 269.5 mm with rack brackets, 1U
Weight 3.6 kg

Full features

  • 4‑channel amplifier, with a total powerTANK capacity of 600 W
  • dualCOOL convection cooling with additional intelligent fan in case of extreme thermal conditions
  • ecoRAIL and APD deliver significant reduction in power consumption
  • Variable Load Drive (VLD) providing the same power into 4 Ω, 8 Ω, 70 V or 100 V
  • amp‑LINK single cable solution for easy installation
  • powerTANK

    • powerTANK is a reservoir of available amplification power that is deployed flexibly across the 4 channels of the amplifier. There is no need to set up the powerTANK as it adapts to the requirements of each zone or output without extra manual configuration of each individual channel.
  • Variable Load Drive

    • Variable Load Drive (VLD) ensures that the powerTANK capacity is utilized efficiently, providing consistent power to any channel with any impedance. dualCOOL The dualCOOL thermal design means that the amplifier typically operates as a convection cooled amplifier, but in extreme thermal conditions the amplifier is also equipped with an intelligent multi‑speed fan to ensure maximum performance and reliability in any application.
  • ecoRAIL

    • ecoRAIL’s power consumption is similar to a regular standby level, yet ecoRAIL still produces audio output suitable for background music levels, and the Auto Power Down (APD) mode can be engaged to further reduce power consumption to less than a watt when there is no signal present for extended periods.
  • PFC power supply

    • Equipped with a PFC power supply and protection features usually reserved for the professional power amplifiers, means that the amplifier resists complete shutdown situations and will always perform at its best under all conditions.

Full specifications

General

  • Signal processing: Input Routing, HPF 24 dB/ Oct., LPF 24 dB/Oct., Flat, Peak Limiter
  • Power requirements: 100 V to 240 V, 50 Hz to 60 Hz AC
  • Power consumption:
    • Consumption at 1/8 rated output power 115 W
    • Idle mode (ecoRAIL with no input signal) < 20 W
    • Standby mode (APD active) < 1 W
  • Power supply topology: Switching power supply with power factor correction
  • Protections: Audio limiters, high temperature, DC, HF, short circuit, back‑EMF, peak current limiters, inrush current limiters, mains over/under voltage protection
  • Front status LEDs: Signal, limit, fault LEDs per channel; power LED
  • Rated Power @ 4Ω, 8Ω, 70V, 100V: 4 x 150 W
  • Maximum output power per channel (power sharing): 300 W
  • Total rated output power: 600 W

Connectivity

  • Analog Audio Input:
    • Type: 2 x 6‑pin Euroblock, 3.81 mm, male, parallel 1x RJ45 AMP‑LINK
    • Maximum input level (LEVEL 0 dB): +18 dBu
    • Input impedance, active balanced: 20 kΩ
  • Mains Input: IEC C14
  • Loudspeaker output: 2 x 4-pin Euroblock, 5.08 mm, female
  • Control Port:
    • Type 1 x 5‑pin Euroblock, 3.81 mm, male
    • REMOTE ON Remote On / Standby contact (overrides power button on front panel) READY/FAULT: Galvanic isolated relay, max. 30 VDC / 500 mADC

Climatic conditions

  • Cooling concept: Convection cooling in tabletop application and rack application with spacing between units. Forced cooling (side to rear) in rack application without spacing between units and in extreme thermal conditions.
  • Ambient temperature limits: -5 °C to +45 °C (+23 °F to +113 °F)
  • Altitude (operating): -500 m to +5000 m (-1614 ft to 16404 ft)

Enclosure

  • IEC Protection Class: Class I (grounded)
  • Dimensions (HxWxD)
    • With 19” mounting brackets 44.2 x 483 x 269.5 mm
    • (1.74 x 19.2 x 10.6 in)
  • Weight: 3.6 kg (7.9 lb)

See Datasheet in Downloads tab for power specifications

Product Reviews

No reviews yet — be the first to review this product.

Similar Products

Frequently Asked Questions

We’re a working touring and events production company founded in 2019 by sound engineers with many years of experience. 

We’re very selective about the products we sell. Everything we supply we use ourselves on our tours, events and productions. This means we can offer a level of buying advice and aftersales support that can’t be beaten.

We’re official dealers of brands such as Allen & Heath, Audio Technica and sE Electronics. We also stock other leading brands including Shure, Sennheiser, Martin Audio and Chauvet Professional.

We accept Visa, Mastercard, American Express, Apple Pay, Google Pay and Paypal. We also offer finance through Paypal Credit and Klarna.

Business Customers can choose to receive a Proforma Invoice on checkout to pay by bank transfer.

Yes. We run an AV production business and have AV Engineers on hand to provide advice and technical support during our operating hours.

The quickest way to contact us for advice and support is through WhatsApp or Email.

Many of our customers are trade/industry buyers and we have already factored this into our pricing. Trade discounts may be available for bulk quantities on some products.

We also offer quantity discounts on some products on our website.

You can order on our website for delivery to the UK (Including Northern Ireland), Isle of Man, Jersey, Guernsey and the Republic of Ireland.

We can ship many items to the EU and other countries worldwide. Our dealer agreements may prevent us sending some items to certain countries.

Please contact us for a quotation if you need something shipped to a country not offered at checkout.

Please see our Returns page for information on our returns policy and to start a return online.

Generally if you change your mind you can return your item for a full refund within 30 days of delivery (14 days for business customers) - as long as the product is unopened and unused.

If an item is faulty or damaged we will arrange collection free of charge and repair/replace it as quickly as possible.

Estimated delivery times are shown on the product page. For items in stock we aim to get your order to you within 1 - 2 working days.

Some items are ordered directly from the manufacturer. These may have longer lead times which will be estimated on the product page. Please contact us for a more accurate lead time.

Yes. We have a trade counter near Wembley Stadium, London. Many of our most popular items are stocked here for immediate collection.

Stock availability is shown on every product page and is updated in real time. Items not stocked at our Wembley branch can usually be collected next day.

We're currently not able to offer an installation service due to the rapid growth of Stage Supply.

We hope to be able to offer this service again in the future.

We use Royal Mail for smaller items, FedEx and Parcelforce for larger items and The Pallet Network for Pallet delivery items.

Tracking for your order is provided on dispatch.