Lab Gruppen E8:2 Energy Efficient Class-D Amplifier 2×400W 19″ 1U

Product code: 180396

£721.00 inc VAT
£600.83 ex VAT

SKU: 000-DFF04-00010

2 in stock

In stock with Lab Gruppen - ordered on demand
FREE delivery by ThursdayOrder by 3pm tomorrow
Click & Collect Wednesday ›Collect from us in Wembley
VisaMastercardAmerican ExpressApple PayGoogle PayPayPalPayPal Credit
1 Year Manufacturer Warranty Included

About this Product

The Lab Gruppen E8:2 delivers 2 × 400 W from a 4.2 kg, 1U chassis, sitting in the middle of the two-channel E Series for commercial install work. Each channel switches between Lo-Z loads down to 2 Ω and 70 V constant-voltage lines, and asymmetric loading lets one channel feed a distributed ceiling run while the other drives a low-impedance pair or sub. The IDEEA Class-D stage, Energy Star certification and sub-1 W standby keep mains draw, heat and lifetime running costs low.

2 × 400 W
Output power
2 Ω
Minimum load
70 V
Hi-Z mode
<1 W
Standby draw
RSL mode and 8/16 Ω loadsThe per-channel RSL switch sets the limiter for Lo-Z or 70 V operation, and it affects available power: an 8 Ω load gets the full 400 W only in 70 V mode (Lo-Z gives 200 W), and a 16 Ω load gets 290 W in 70 V mode (Lo-Z gives 100 W). The amplifier can also deliver 400 W to a 100 V line tapped at 800 W. Match the switch to the connected load during commissioning.

Features

800 W across 2 flexible output channels in a 1U form factor
Energy Star certified with exceptionally low lifetime running costs
IntelliDrive delivers 2 × 400 W at 70 V constant voltage or into 2, 4 and 8 Ω loads
Asymmetric channel loading mixes different impedances on one amplifier
Proprietary IDEEA Class-D output stage
Rail Sense Limiter (RSL) greatly reduces signal clipping and simplifies configuration
Auto-standby and auto-power-on cut consumption to below 1 W between uses
Built-in 50 Hz high-pass filter, switchable per channel on the rear panel
Per-channel attenuation knob and signal LED on the rear panel for commissioning
Temperature-controlled fan with front-to-back airflow
Aluminium front panel with power, temperature and per-channel signal/limit LEDs
GPIO connector with power control and indication for system integration
Balanced analogue inputs and amplifier outputs on detachable screw terminals
Comprehensive fail-safe circuit protection

Specifications

Lab Gruppen E8:2 Energy Efficient Class-D Amplifier 2×400W 19″ 1U specifications
Amplifier channels 2
Max total output, all channels driven 800 W
Output per channel 400 W into 2 Ω, 4 Ω or 70 V; 400 W into 8 Ω in 70 V mode (200 W in Lo-Z); 290 W into 16 Ω in 70 V mode (100 W in Lo-Z); 400 W to a 100 V load tapped at 800 W
Peak output voltage per channel 100 V / 70 Vrms
Max output current 16 Arms
THD (20 Hz – 20 kHz @ 1 W) <0.1%
THD (@ 1 kHz, 1 dB below clipping) <0.05%
Signal-to-noise ratio >112 dBA
Channel separation @ 1 kHz >70 dB
Frequency response 2 Hz – 40 kHz
Input impedance 20 kΩ
Common mode rejection 50 dB
Gain 35.2 dB (70 V mode); 30.3 dB (Lo-Z mode)
Level adjustment Rear panel potentiometer per channel, -inf to 0 dB
Input connectors 3-pin detachable screw terminals, electronically balanced (per channel)
Output connectors 2-pin detachable screw terminals (per channel)
High-pass filter Fixed 50 Hz, switchable per channel
GPIO Contact-closure GPI power control and GPO power-state output on 2-pin screw terminals
Cooling Single fan, front-to-rear airflow, temperature-controlled speed
Mains 100-240 VAC nominal (70-265 VAC operating), IEC inlet
Standby consumption <1 W
Dimensions (W × H × D) 483 × 44 × 276 mm (1U, 19″)
Weight 4.2 kg
Finish Dark grey aluminium front, black steel chassis
Approvals CE, RoHS, WEEE, UL 60065, CSA C22.2 No. 60065, FCC Part 15 Subpart B Class A, PSE, CCC, Energy Star
Warranty 1 year

Full features

  • 800 W amplifier carrying 2 flexible output channels in a high power density 1 rack unit form factor saves rack space and system cost
  • Energy efficient with Energy Star* certification for supreme green credentials and exceptionally low lifetime running costs
  • Flexible IntelliDrive permits delivering the 2 x 400 W at constant voltage 70 V or low impedance (2, 4 and 8 Ohms) on any channel
  • Asymmetric channel loading allows mixing and matching loads with different impedances to maximize overall system efficiency and inventory utilization
  • High efficiency amplifier with low power consumption and minimized heat generation lowers demands on the installations' mains distribution and cooling systems
  • IDEEA outputs stage based on proprietary, state-of-the-art Class-D amplifier technology for superior performance
  • Comprehensive fail safe circuit protection ensures continued operation even under reduced operating conditions
  • Auto-standby and auto-power-on reduces power consumption to below 1 W in non-operating cycles
  • Rail Sense Limiter (RSL) greatly reduces signal clipping and ensures simple configuration for constant voltage and low impedance loads
  • Built in 50 Hz high pass filter selectable per channel available on rear panel switch
  • Per-channel attenuation knob and signal LED on rear panel for simple commissioning
  • Efficient cooling with temperature-controlled fan with front to back airflow
  • Aluminum front panel with power and temperature LEDs and per-channel signal and limit LEDs
  • GPIO connector with power control and indication for further system integration
  • Balanced high-quality analog inputs and amplifier outputs on detachable screw terminals

Full specifications

General

  • Number of amplifier channels: 2
  • Max total output all channels driven: 800 W
  • Peak output voltage per channel: 100 V / 70 Vrms
  • Max. output current: 16 Arms

Max output power (all channels driven)

  • 2 ohms: 400 W
  • 4 ohms: 400 W
  • 8 ohms: 400 W (requires the “70 V” mode for the RSL, “Lo-Z” gives 200 W)
  • 16 ohms: 290 W (requires the “70 V” mode for the RSL, “Lo-Z” gives 100 W)
  • 70 V: 400 W
  • 100 V: Can deliver 400 W to a 100 V load tapped at 800 W

Performance

  • THD 20 Hz - 20 kHz at 1 W: <0.1%
  • THD at 1 kHz and 1 dB below clipping: <0.05%
  • Signal to Noise Ratio: >112 dBA
  • Channel separation (Crosstalk) at 1 kHz: >70 dB
  • Frequency Response: 2 Hz - 40 kHz
  • Input impedance: 20 kOhm
  • Common Mode Rejection (CMR): 50 dB
  • Output impedance: 25 mOhm

Gain, Sensitivity and Limiters

  • Limit and gain switch defining limit and gain (per channel): 2 pos: Lo-Z and 70 V
  • VPL for 70 V mode: 100 V
  • VPL for Lo-Z mode: 56.6 V
  • Sensitivity for stated power into 4 Ohm in Lo-Z mode: 4 dBu
  • Sensitivity for 70.7 V out in 70 V mode: 4 dBu
  • Sensitivity for stated power into 2 Ohm in Lo-Z mode: 1 dBu
  • Sensitivity for stated power into 8 Ohm in 70 V mode: 2.1 dBu
  • Sensitivity for stated power into 16 Ohm in 70 V mode: 3.7 dBu
  • Gain in 70 V mode: 35.2 dB
  • Gain in Lo-Z mode: 30.3 dB
  • Level adjustment (per channel): Rear panel potentiometer, from -inf to 0 dB

Connectors and Buttons

  • Input connectors (per ch.): 3 - pin detachable screw terminals, electronically balanced
  • Output connectors (per ch.): 2 - pin detachable screw terminals
  • High pass filter: Fixed at 50 Hz, switchable per channel
  • Power control: Can be used to go between standby and ON
  • GPI (power control input): Contact closure type, 2-pin detachable screw terminal, controls the power state
  • GPO (power state output): Contact closure type, 2-pin detachable screw terminal, for external monitoring of the power state
  • Cooling: Single fan, front to rear airflow, no filter required, temperature controlled speed

Power

  • Nominal voltage: 100 – 240 VAC
  • Operating voltage: 70 – 265 VAC
  • Standby consumption: <1 W
  • Mains connector: IEC inlet

Dimensions

  • Dimensions: W: 483 mm (19”), H: 44 mm (1 U), D: 276 mm (10.9”)

Weight

  • Weight: 4.2 kg (9.3 lbs)

Finish

  • Finish: Dark grey aluminum front and black steel chassis

Approvals

  • Approvals: CE, RoHS, WEEE, UL (UL 60065), CSA C22.2 NO. 60065, FCC Part 15 Subpart B Class A, PSE, CCC Energy Star
Compare the Range
Lab Gruppen E8:2 Energy Efficient Class-D Amplifier 2×400W 19″ 1U
Lab Gruppen E8:2 Energy Efficient Class-D Amplifier 2×400W 19″ 1U
£721.00 inc VAT
£600.83 ex VAT
  • Amplifier channels: 2
  • Signal-to-noise ratio: >112 dBA
  • Standby consumption: <1 W
  • Weight: 4.2 kg
Viewing Now
Lab Gruppen E2:2 Energy Efficient Class-D Amplifier 2×100W 19″ 1U
£536.00 inc VAT
£446.67 ex VAT
  • Amplifier channels: 2
  • Signal-to-noise ratio: >112 dBA
  • Standby consumption: <1 W
  • Weight: 4.2 kg
View →
Lab Gruppen E4:2 Energy Efficient Class-D Amplifier 2×200W 19″ 1U
£628.00 inc VAT
£523.33 ex VAT
  • Amplifier channels: 2
  • Signal-to-noise ratio: >112 dBA
  • Standby consumption: <1 W
  • Weight: 4.2 kg
View →
Lab Gruppen E 20:4 Energy Efficient Class-D Amplifier 4×500W 19″ 1U
£1,572.00 inc VAT
£1,310.00 ex VAT
  • Amplifier channels: 4
  • Signal-to-noise ratio: >106 dBA
  • Mains: 100-240 VAC, standard IEC receptacle
  • Standby consumption: <2.5 W
  • Weight: 7.9 kg
View →
Lab Gruppen E 40:4 Energy Efficient Class-D Amplifier 4×1000W 19″ 1U
£1,757.00 inc VAT
£1,464.17 ex VAT
  • Amplifier channels: 4
  • Signal-to-noise ratio: >106 dBA
  • Mains: 100-240 VAC, standard IEC receptacle
  • Standby consumption: <2.5 W
  • Weight: 7.9 kg
View →
Lab Gruppen E10:4 Energy Efficient Class-D Amplifier 4×250W 19″ 1U
£1,202.00 inc VAT
£1,001.67 ex VAT
  • Amplifier channels: 4
  • Signal-to-noise ratio: >112 dBA
  • Standby consumption: <1 W
  • Weight: 6.2 kg
View →
Lab Gruppen E12:2 Energy Efficient Class-D Amplifier 2×600W 19″ 1U
£813.00 inc VAT
£677.50 ex VAT
  • Amplifier channels: 2
  • Signal-to-noise ratio: >112 dBA
  • Standby consumption: <1 W
  • Weight: 4.2 kg
View →

Product Reviews

No reviews yet — be the first to review this product.

Similar Products

Frequently Asked Questions

We’re a working touring and events production company founded in 2019 by sound engineers with many years of experience. 

We’re very selective about the products we sell. Everything we supply we use ourselves on our tours, events and productions. This means we can offer a level of buying advice and aftersales support that can’t be beaten.

We’re official dealers of brands such as Allen & Heath, Audio Technica and sE Electronics. We also stock other leading brands including Shure, Sennheiser, Martin Audio and Chauvet Professional.

We accept Visa, Mastercard, American Express, Apple Pay, Google Pay and Paypal. We also offer finance through Paypal Credit and Klarna.

Business Customers can choose to receive a Proforma Invoice on checkout to pay by bank transfer.

Yes. We run an AV production business and have AV Engineers on hand to provide advice and technical support during our operating hours.

The quickest way to contact us for advice and support is through WhatsApp or Email.

Many of our customers are trade/industry buyers and we have already factored this into our pricing. Trade discounts may be available for bulk quantities on some products.

We also offer quantity discounts on some products on our website.

You can order on our website for delivery to the UK (Including Northern Ireland), Isle of Man, Jersey, Guernsey and the Republic of Ireland.

We can ship many items to the EU and other countries worldwide. Our dealer agreements may prevent us sending some items to certain countries.

Please contact us for a quotation if you need something shipped to a country not offered at checkout.

Please see our Returns page for information on our returns policy and to start a return online.

Generally if you change your mind you can return your item for a full refund within 30 days of delivery (14 days for business customers) - as long as the product is unopened and unused.

If an item is faulty or damaged we will arrange collection free of charge and repair/replace it as quickly as possible.

Estimated delivery times are shown on the product page. For items in stock we aim to get your order to you within 1 - 2 working days.

Some items are ordered directly from the manufacturer. These may have longer lead times which will be estimated on the product page. Please contact us for a more accurate lead time.

Yes. We have a trade counter near Wembley Stadium, London. Many of our most popular items are stocked here for immediate collection.

Stock availability is shown on every product page and is updated in real time. Items not stocked at our Wembley branch can usually be collected next day.

We're currently not able to offer an installation service due to the rapid growth of Stage Supply.

We hope to be able to offer this service again in the future.

We use Royal Mail for smaller items, FedEx and Parcelforce for larger items and The Pallet Network for Pallet delivery items.

Tracking for your order is provided on dispatch.